POTENTIOMETER / F11K
F11K Series 11mm Insulated Shaft Potentiometer
11 mm insulated-shaft rotary potentiometer with resin insert moulding around the resistor to prevent flux build-up. Single or dual gangs, top or side adjust PC pins, optional bushing and detents; standard life of at least 15,000 cycles or long life of at least 100,000 cycles.
Selection follows the downloadable PDF; confirm production specifications with our team. For F shafts with a bushing, length code 7 is 27.5 mm in the PDF but 28.7 mm in the supplied printed sheet; confirm before ordering. The general table lists tapers A/B/C, while the ordering table also lists D (10A); confirm the required taper.
| Parameter | Value |
|---|---|
| Total resistance | 1KΩ ~ 1MΩ |
| Total resistance tolerance | 500Ω < R < 1MΩ: ±20%; R ≤ 500Ω / R ≥ 1MΩ: ±30% |
| Resistance taper | A / B / C; ordering table also lists D (10A) |
| Max. operating voltage | Single: AC 50V, DC 20V; dual: AC 30V |
| Rated power | Single: 0.05W; dual: 0.025W |
| Rotational noise | Less than 100mV |
| Insulation resistance | Single: >100MΩ at DC 500V; dual: >100MΩ at DC 250V |
| Withstand voltage | Single: AC 500V for 1 minute; dual: AC 300V for 1 minute |
| Residual resistance | Term. 1–2 <20Ω; Term. 2–3 <20Ω |
| Gang error (dual unit) | −40dB ~ 0dB: ±3dB |
| Total rotational angle | 300° ± 10° |
| Rotational torque | 20 ~ 100 gf·cm |
| Click torque | 50 ~ 180 gf·cm |
| Stopper strength | ≥3.0 kgf·cm |
| Push-pull strength | ≥8.0 kgf |
| Rotational life | Standard: ≥15,000 cycles; long life: ≥100,000 cycles |
| Operating temperature range | −10°C ~ +70°C |
| Parameter | Value |
|---|---|
| Gang and terminal configuration | N: single; G: dual. H: top adjust PC pins; V: side adjust PC pins |
| Mounting height | H top adjust: code 0 (not applicable); V side adjust: code 1 = 10 mm, code 2 = 12.5 mm |
| Bushing and shaft types | No bushing or M9 × P0.75 bushing; F flatted shaft or Y 18-tooth knurled shaft, approx. Ø6 mm |
| Shaft length range | F: 15–36.2 mm without bushing, 12.5–27.5 mm with bushing. Y: 15–35 mm without bushing, 12.5–27.5 mm with bushing. Individual code dimensions appear in the builder. |
| Full CCW position | F: C / D; Y: A. Drawing angle 30° ± 10°; confirm knob orientation against the PDF. |
| Detent option | 0: no detent; 1: centre detent; 2: 11 detents; 3: 21 detents |
| Drawing variants | NH00 / NH01 / NV20 / NV11 / GH00 |
| PCB layout | Single-gang top-adjust terminal pitch 2.5 mm, span 7.5 mm; dual-gang PCB drawing has 6 electrical terminal holes. Refer to PDF drawings for variant mounting holes and tolerances. |
General values are typical references; confirm production specifications with our team.
HOW TO ORDER / F11K
Part number builder
Pick each option and the full P/N is generated below. Send us the P/N and we know exactly what you need.
What this P/N means
Every code is translated into its actual specification. If anything remains unclear, send the complete P/N to our live team.
- Gang number · N
- Single gang
- Terminal configuration · H
- Top adjust, PC pins
- Mounting height · 0
- Not applicable (top adjust)
- Bushing option · 0
- Without bushing
- Detent option · 0
- No detent
- Shaft type · F
- F flatted shaft
- Shaft length code · 1
- Code 1 · L 15 mm · F 4.5 mm · H 10.5 mm
- Full CCW position · C
- Position C (F shaft)
- Resistance taper · A
- Audio (15A)
- Total resistance · 1K
- 1K
- Operation life · —
- Std. life w/o anti-sulfur